← Back to KB navigation
Equipment H-101
FM damper_sticking
ISO 14224 mode LOO Low output
Source OPC Ontology KB
挡板卡涩 (Damper Sticking)
H-101 · fired_heater
Related equipment → H-101
0.82Source conf.
0.65Evidence conf.
LOOISO 14224 mode
1Failure Mechanism
Function:调节烟气流量控制炉膛负压
Failure cause:烟气中粉尘在转轴处沉积结垢；高温下金属热膨胀导致间隙消失；润滑不良或轴承损坏
Damage mechanism：粉尘结垢 + 热膨胀卡涩（damper sticking, fouling + thermal expansion）
2Source Basis (where this FM comes from)
OPC Ontology KBCSB Accident DBQuant benchmark
Source confidence 0.82: this FM is derived from the ontology KB and cross-validated by OPC Ontology KB·CSB Accident DB·Quant benchmark.
3Evidence Chain (supporting basis)
Evidence text：None
Evidence conf.：0.65 · Evidence source：engineering_estimate
Governing standards (evidence)：std:API-560 — API STD 560 — Fired Heaters for General Refinery Service · 管式加热炉设计std:API-570 — API 570 — Piping Inspection Code · 工艺管道检验
4Related Real Accidents (traceable to accident cards)
This FM is recorded in 3 real accident investigation(s); tap the report no. to open the corresponding accident lesson card.
5Applicable Standards & Clauses
API 580GB/T 7826-2012ISO 14224:2016SAE JA1011_202411
Standard clause references (22):
GB/T 7826-2012GB/T 27921-2011GB/T 36894-2018GB/T 44958-2024GB/T 37243-2019GB/T 4888-2008GB/T 29639-2020AQ/T 3034-2022API 581API 580API 510API 570API 571API 579-1/ASME FFS-1API 754API 576API 689API 755ISO 14224:2016ISO 20815:2018IEC 61511:2016ISO 31000:2018
6Derived Analysis (seeded from this FM)
6/4/4FMEA Sev/Occ/Det
0.34RBI λ
0.55Monitor pdet
4 月Insp. int.
Current tasks:检查挡板动作灵活性 | 清理转轴和叶片积灰 | 润滑转轴
RCFA incident:H-101 发生挡板卡涩 (Damper Sticking)，严重程度 6，后果类型 Safety
7RCM Maintenance Decision (strategy landing)
CBMOn-Condition Maintenance
Recommended task按压差/效率监测设定清洗周期 + 过滤/防堵维护; 沉降/变形观测 + 支撑/基础评估; 标定/零点-跨度校验 + SIL Proof test + 阀门行程试验 + 变更管理; 无损检测(UT/VT/MT/PT), 按 API 581 RBI 风险定级设定检验间隔; 温度/红外热成像监测, 超温报警与根因排查
Suggested intervalHigh risk 1-3 mo / Medium 6-12 mo / Low risk at turnaround (by API 581 RBI risk ranking)
Decision basis机理类别=corrosion; deformation; fouling; instrument; overheat
Governing standardsAPI 530API 570API 571API 579API 581API 653GB/T 21109IEC 61511ISA 84厂家规范
⚠ This decision is engineering-inferred by RCM logic from the damage mechanism / root cause / failure cause — it is not derived from measured site history. Confirm with the equipment owner and process before execution.
⚠ 本卡技术正文（功能 / 致因 / 损伤机理 / RCFA 叙事）保留中文原文——依可信 AI 红线，自由技术文本不自动机翻、不编造英文译文。UI、设备类型、FM 名、ISO 码、标准号均为英文。